Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
This great article in the next paragraphs on the subject of Tools You Need to Install a New Bathtub is extremely attention-grabbing. Don't bypass it.
Setting up a bath tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a new one is also a reasonably difficult job. If the old bathtub is conveniently obtainable, the job can move immediately; if you have to open up a wall surface to eliminate the old tub as well as position the new tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the job and also are comfortable trying it. Rather than hiring a professional to take over a halfway-completed project, it is far better to consider utilizing one before you start. Chances are you may require a professional plumber to make tube connections.
This write-up will certainly help you mount a brand-new bathtub in your bathroom if you have already gotten a new bathtub as well as don't need to transform the plan of your previous water pipes.
Your tools and also material list should comprise the following:
Preparing for the Setup
First of all, the sustaining framework supplied with the bath ought to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps device to stop strain on the tub.
Fit the flexible tap ports to the bottom of both faucets utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, switch on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be rather bothersome due to the restricted access that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing both wood boards under its feet, put the bathtub in the called for placement. The wood boards are practical in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub until the level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the water system and also examine all joints as well as new pipework for leakages and also tighten them if essential. Load the tub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the producer's instruction manual. Tiling and sealing around the tub must wait up until the tub has actually been used at the very least when as this will settle it into its last setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the tap and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind should be linked to the tap ends first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack a stiff seal, creating the water to pass through the wall between the bathroom and also the tiling, resulting in problems with dampness and possible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also installations. They are offered in tubes and also cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can crack fairly early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that blog posting about A Step-by-Step Guide to Installing a Bathtub while doing a lookup on the search engines. Sharing is caring. One never knows, you could be doing someone a favor. Thank you so much for going through it.
Estimate Free
Report this page